桁車式刮泥機電控柜如何接線
保護接地和相關電氣接點是否可靠連接，送電后應檢查三相電壓是否正常。 集泥斗、集楂槽分設兩端（tgnz—f型）正常提供電控工作方式為：
（1）手動方式：
a. 合上電源開關；
b. 將選擇開關sa置于“手動”檔；
c.啟動提升減速機刮泥耙(pa)上提、撇渣板下降至液面設定位置；
d.啟動行車正行程運行，反行程限位燈滅，正行程運行燈亮，到終端限位時停機，正行程運行燈滅，正行程終端限位燈亮，行車停止工作；
e.啟動提升減速機刮泥耙(pa)下降、撇渣板上提至設定位置；
f. 啟動行車反行程運行，正行程限位燈滅,反行程運行燈亮，到達始端反行程限位時反行程限位燈亮,反行程運行燈滅，行車返回起始位置停機。完成一次循環。
說明：手動控制主要是為安裝、調試、檢修設置的，行車、刮泥耙及撇渣板運行除受手動按扭控制外，同時也受行程限位開關約束。
（2） 自動控制： 自動控制工作方式及條件：首先，行車應處于反行程限位處即正行程起始端。集泥斗、集楂槽分設兩端時，刮泥耙應處于下降行程限位位置。
a. 合上雙匹控制回路電源開關，將選擇開關置于“自動”檔，將刮泥機連續往返計數器
復零按鈕按下。依工藝條件在時間繼電器（kt3）上整定好行車每次行走工作間隔時間（一般為1-3次），然后，在計數器上整定好行車每次行走工作要求連續往返的次數， ，在時間繼電器（kt1、kt2）上整定好刮泥耙(pa)上提、下降及行車正、反行走間隔時間（一般為15-30秒）。 b.合上電源總開關和橋架、提升的分電源開關；
